- Home
- Pressure Sensor
- Transmitter
- Pressure Transmitters Standard
- Level Pressure Transmitter
- Vacuum Pressure Transmitters
- Differential Pressure Transmitter
- High Temperature Pressure Transmitters
- Pressure Transmitter
- Micro Pressure Transmitters
- Temperature Transmitters
- Digital Pressure Gauges
- Digital Pressure Switchs
- Switch and Display
- About Us
- News
- Contact
Call Us: 0086 18795888617 / [email protected]
TYPE:JC-CZ28
NAME:JC-CZ28 2” Clamp Oil Filled Pressure Sensor
JC-CZ28 2’’ clamp oil filled pressure sensor is a silicon piezoresistive sensor based on MEMS technology. It is a high stability and high precision OEM pressure measuring sensor.
MESSAGEJC-CZ28 2” Clamp Oil Filled Pressure Sensor Introduction:
JC-CZ28 2” clamp oil filled pressure sensor is a silicon piezoresistive sensor based on MEMS technology. It is a high stability and high precision OEM pressure measuring sensor. The series is packaged by pressure chips from internationally renowned manufacturers. 2″ clamp connector for front end, external pressure is transmitted to the sensitive component through 316L stainless steel diaphragm and internal filling silicone oil, which can be used to measure all pressure media compatible with 316L stainless steel.
Each sensor was strictly temperature compensated for both zero and span.
It provides two power supply options: constant current and constant voltage.
JC-CZ28 2” Clamp Oil Filled Pressure Sensor Features:
* High stability, high precision
* Suitable for small and medium pressure (0-40Kpa…2.5Mpa)
* Wide temperature compensation range
* Measure corrosive media (compatible with 316L)
* Typical output：0-100Mv
JC-CZ28 2” Clamp Oil Filled Pressure Sensor Application:
* Process control
* Fresh and waste water measurements
* Medical and food instruments
* Pressure transmitters
* Level measurement
Dimensions(mm):
Specifications of current excitation(1.5mA, 25℃)
| Parameters | Min. | Typical | Max. | |
| Accuracy(%FS) | 40Kpa | ±0.20 | ±0.30 | |
| Non-Linearity1 | >40Kpa | ±0.10 | ±0.20 | |
| Hysteresis2 | ±0.05 | ±0.10 | ||
| Repeatibility3 | ±0.05 | ±0.10 | ||
| Zero Output(mV) | -2 | ±1 | 2 | |
| Span(FS) Output(mV) | 70 | |||
| Operation Temp.(℃) | -40 | 125 | ||
| Compensated | 40Kpa | 0 | 50 | |
| Temp.(℃) | ≥100Kpa | -10 | 70 | |
| Zero Temp.error(%FS)4 | ±0.75 | ±1.0 | ||
| Span Temp. error(%FS)4 | ±0.75 | ±1.0 | ||
| Temperature hysteresis(%FS)5 | 0.1 | |||
| Long term Stability/Zero (±%FS annual) | 0.1 | |||
| Long term Stability/Span (±%FS annual) | 0.1 | |||
| Supply Current(mA) | 0.5 | 1.5 | 2 | |
| Input Resistance(KΩ) | 2 | 2.5 | 3 | |
| Output Resistance(KΩ) | 2.5 | 3 | 3.7 | |
| Load Resistance6(MΩ) | 5 | |||
| Insulation Resistance(100V)7(MΩ) | 100 | |||
Specifications of voltage excitation (10VDC 25℃)
| Parameters | Min. | Typical | Max. | |
| Accuracy(%FS) | 40Kpa | ±0.20 | ±0.30 | |
| Non-Linearity1 | >40Kpa | ±0.10 | ±0.20 | |
| Hysteresis2 | ±0.05 | ±0.10 | ||
| Repeatibility3 | ±0.05 | ±0.10 | ||
| Zero Output(mV) | -2 | ±1 | 2 | |
| Span(FS) Output(mV) | 98 | 100±1 | 102 | |
| Operation Temp.(℃) | -40 | 125 | ||
| Compensated | 40Kpa | 0 | 50 | |
| Temp.(℃) | ≥100Kpa | -10 | 70 | |
| Zero Temp.error(%FS)4 | ±0.75 | ±1.0 | ||
| Span Temp. error(%FS)4 | ±1 | ±1.2 | ||
| Temperature hysteresis(%FS)5 | 0.1 | |||
| Long term Stability/Zero (±%FS annual) | 0.1 | |||
| Long term Stability/Span (±%FS annual) | 0.1 | |||
| Supply Voltage(VDC) | 10 | 14 | ||
| Input Resistance(KΩ) | 6 | 8 | 10 | |
| Output Resistance(KΩ) | 2.5 | 3 | 3.7 | |
| Load Resistance6(MΩ) | 5 | |||
| Insulation Resistance(100V)7(MΩ) | 100 | |||
| Pressure Range | 0-40Kpa…2.5Mpa | |||
| Overpressure | 2X | |||
| Media–Pressure | Liquids and gases compatible with 316L Stainless Steel | |||
Remark
1. Best fit straight line.
2. The pressure sensor performs the pressure from the minimum value to the maximum value (positive stroke) and the maximum value to the minimum value (reverse stroke), and the deviation of the output value at any pressure within the pressure range from the forward stroke to the reverse stroke;
3. In the same test method as in 2, perform 3 forward and reverse stroke pressure cycles;
4. Compared with the output of 25 °C in the compensation temperature range
5. Zero output is the deviation value before and after the sensor performs a temperature cycle of -40~+125°C.
6. Increase the load resistance to reduce the measurement error
7. Between the lead and the outer casing
| JC-CZ28 Pressure Sensor | |||||
| Model | Description | ||||
| JC-CZ28 | 2” Clamp Oil Filled Pressure Sensor | ||||
| Code | Power Supply | ||||
| C | Constant current | ||||
| V | Constant Voltage | ||||
| Code | Pressure Range | Gauge | Absolute | ||
| 40K | 0-40Kpa | * | |||
| 100K | 0-100KPa | * | * | ||
| 160K | 0-160KPa | * | * | ||
| 400K | 0-400KPa | * | * | ||
| 600K | 0-600KPa | * | * | ||
| 1M | 0-1MPa | * | * | ||
| 1.6M | 0-1.6MPa | * | * | ||
| 2.5M | 0-2.5MPa | * | * | ||
| XXX | Customized | ||||
| Code | Pressure type | ||||
| G | Gauge | ||||
| A | Absolute | ||||
| SG | Seal Gauge | ||||
| Code | Fitting | ||||
| 2 | Ribbon Cable (90mm as default) | ||||
| X | Customized | ||||
Note: Food grade oil-filled sensors are also available and need to be customized
1. Can be used for down-range, and the amplitude is controlled within ±50%FS.
2. The maximum pressure of the system should be less than the overload protection limit of the sensor, otherwise it will affect the service life of the product and damage the product.
3. The commonly used compensation method for products is 1.5mA constant current compensation.
4. Do not force to pull the pins or the leads of sensitive components.
5. Protect the isolation diaphragm at the front end of the pressure sensitive component to prevent the impact of the pressure sensitive component from damaging the sensitive component.
6. If you have special requirements on product performance parameters and functions, please contact us.
