• JC-CZ12 Flush Diaphragm Pressure Sensor
  • JC-CZ12 Flush Diaphragm Pressure Sensor
  • JC-CZ12 Flush Diaphragm Pressure Sensor
  • JC-CZ12 Flush Diaphragm Pressure Sensor
  • JC-CZ12 Flush Diaphragm Pressure Sensor

TYPE:JC-CZ12

NAME:JC-CZ12 Flush Diaphragm Pressure Sensor With Fitting (0-40Kpa…10Mpa, 0-100mV, 1.5mA)

JC-CZ12 flush diaphragm pressure sensor are based on piezoresistive silicon pressure sensors packaged in a 316L stainless steel housing.

JC-CZ12 Flush Diaphragm Pressure Sensor Introduction:

JC-CZ12 flush diaphragm pressure sensor are based on piezoresistive silicon pressure sensors packaged in a 316L stainless steel housing. The sensing package utilizes silicon oil to transfer pressure from the 316L diaphragm to the sensing element.

The flush diaphragm pressure transducer was welded in front end of a fitting (M20X1.5 or G1/2 made by Stainless Steel 304). Each sensor was strictly temperature compensated for both zero and span.

JC-CZ12 Flush Diaphragm Pressure Transducer Features:

* Pressure range:0-40Kpa…10Mpa
* Wide operable temperature range -40-125℃
* Compatible with corrosive media
* Standard mounting size
* Typical output:0-100mV

JC-CZ12 Flush Diaphragm Pressure Transducer Application:

* Process control
* Fresh and waste water measurements
* Medical and food instruments
* Pressure transmitters

Dimensions(mm):

JC-CZ12 Flush Diaphragm Pressure Sensor With Fitting

Specifications of current excitation(1.5mA, 25℃)

Parameters Min. Typical Max.
Accuracy(%FS) 40Kpa ±0.20 ±0.30
Non-Linearity1 >40Kpa ±0.10 ±0.20
Hysteresis ±0.05 ±0.10
Repeatibility ±0.05 ±0.10
Zero2 Output(mV) -5 ±1.0 5
Span(FS) Output(mV) 70
Operation Temp.(℃)3 -40 125
Compensated 40Kpa 0 50
Temp.(℃) >40Kpa -10 70
Zero Temp.error(%FS)4 ±0.75 ±1.0
Span Temp. error(%FS)4 ±0.75 ±1.0
Thermal hysteresis(%FS) 0.1
Long term Stability/Zero (±%FS annual) 0.1
Long term Stability/Span (±%FS annual) 0.1
Supply Current(mA) 0.5 1.5 2
Input Resistance(KΩ) 2 2.5 3
Output Resistance(KΩ) 2.5 3 3.7
Load Resistance5(MΩ) 5
Insulation Resistance(100V)6(MΩ) 100
Pressure Range 0-40Kpa…10Mpa
Overpressure ≤4Mpa 2X
7Mpa 1.5X
Pressure Media Liquids and gases compatible with 316L/304L SS
Remark 1. Best fit straight line. 2. Measured at vacuum for absolute (A), ambient for gage (G). 3. Maximum temperature range for product with standard cable is -20°C to +105°C. 4. Over the compensated temperature range with respect to 25°C. 5. Load resistance to reduce measurement errors due to output loading. 6. Between case and sensing element.
JC-CZ12 Pressure sensor
Model Description
JC-CZ12 Flush Diaphragm sensor (SS 304 fitting)
Code Power Supply
C Constant Current
Code Pressure Range Gauge Absolute
40K 0~40KPa *
100K 0~100KPa * *
160K 0~160KPa * *
400K 0~400KPa * *
600k 0~600KPa * *
1M 0~1MPa * *
1.6M 01.6MPa * *
2.5M 0~2.5MPa * *
4M 0~4MPa * *
7M 0~7MPa * *
10M 0~10MPa
XX

Customized

Code Pressure type
G Vent Gauge Pressure(W/O vent tube as default)
GT Vent Gauge Pressure(With vent tube)
A Absolute Pressure
S Sealed Gauge
Code Fitting
1 M20X1.5(Stainless Steel 304)
2 G1/2(Stainless Steel 304)
X Customized
Note: 1. Can provide vacuum test sensor of vent gauge, need consulted with factory 2. Can provide constant voltage sensor as required(Specification refer to JC-CZ11 series) 3. Compared with the output of 25 °C in the compensation temperature range 4. Can be used for down-range, and the amplitude is controlled within ±50%FS. 5. The maximum pressure of the system should be less than the overload protection limit of the sensor, otherwise it will affect the service life of the product and damage the product. 6. The commonly used compensation method for products is 1.5mA constant current compensation. 7. Do not force to pull the pins or the leads of sensitive components. 8. Protect the isolation diaphragm at the front end of the pressure sensitive component to prevent the impact of the pressure sensitive component from damaging the sensitive component. 9. If you have special requirements on product performance parameters and functions, please contact us.

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply

Your email address will not be published. Required fields are marked *